See:
Description

Packages

avnmp.java.dp
avnmp.java.gvt
avnmp.java.load
avnmp.java.log
avnmp.java.lp
avnmp.java.plot
avnmp.java.pp
avnmp.java.start
snmp
snmp.agent

Active Virtual Network Management Prediction (AVNMP) Manual and Installation

This research is funded by DARPA/ITO Contract Number: F30602-98-C-0230 supported by the Air Force Research Laboratory/IF.
The project web site is http://www.crd.ge.com/~bushsf/an

Stephen F. Bush and Amit Kulkarni
(bushsf@crd.ge.com, kulkarni@crd.ge.com)

Running AVNMP

The instructions given in this document assume that the Magician Execution Environment (EE) is being used. Once the Magician EE is setup, there should be a network configuration file in the Magician Four11 directory that describes the EE topology. Start the appropriate Host and Nodes for your configuration. Note that wallclock time on all nodes should be synchronized for best performance.

1. The CLASSPATH must include a path to the base of the avnmp packages. This is the directory into which the the avnmp package is installed. If the package creates a directory called avnmp, then the CLASSPATH should point to the directory in which avnmp resides.
1. The CLASSPATH must include the path to the base of the Magician packages.
2. The CLASSPATH must include a path to the directory immediately above the included snmp package. This would be .../avnmp/java.
3. The CLASSPATH within .../magician/starth must include the class paths listed above.
2. The java compiler must be specified by setting the JAVADIR environment variable to the directory in which bin resides, e.g. "setenv JAVADIR /home/bushsf/java1.3.0/j2sdk1_3_0beta".
1. The Debug level can be set by adjusting the value of AvnmpDebug in your environment, e.g. "setenv AvnmpDebug 255" (See AvnmpDebug).
3. At the Magician host enter (assuming host name is AH-1):
1. send avnmp.java.start.InjectSnmp AH-1 (this injects SNMP instrumentation into the network)
2. send avnmp.java.load.LoadGen AH-1 (this begins a sample application called LoadGen)
3. send avnmp.java.start.Flood AH-1 (this injects the logical processes into the network)
4. send avnmp.java.start.AvnmpSmartDriver AH-1 (this starts the driving process on the host node)
4. An SNMP walk of the MIB at any of the running nodes will display the AVNMP state, application predicted state, and actual application state. The mibs are included in mib-avnmp.txt and mib-loadpred.txt.
5. LoadGen attempts to transmit packets to AN-5. This is currently hardcoded in avnmp.java.load.LoadGen and can be changed and recompiled if necessary.

Installation

1. Uncompress and untar the Java source files. (gunzip avnmp-beta.tar.gz, tar xvf avnmp-beta.tar)
2. Run the top level Make to build the executable code. (make)
3. An example load prediction application is included. (LoadGen)

Getting the Code

1. This package contains the AVNMP code. New versions can be retrieved from http://www.crd.ge.com/~bushsf/an.
2. The Magician execution environment is required to run AVNMP and is available from the University of Kansas or contact Amit Kulkarni.
3. An SNMP client is not required, but is useful for monitoring and managing the system. SNMP packages are available from many sources, one source is http://www.net.cmu.edu/groups/netdev/software.html.

This should be enough information to start running. The remaining content of this file provides more detail about the program organization and customization.

AVNMP FILES and Java Packages

The complete AVNMP documentation is found in the AVNMP API .

Startup

• avnmp/java/start/AvnmpSmartDriver.java
This is the AVNMP Driving Process.
• avnmp/java/start/InjectSnmp.java
Inject SNMP instrumentation into the system.
• avnmp/java/start/SnmpAgentMain.java
This starts an SNMP agent on a node.
• avnmp/java/start/Flood.java
This places AVNMP Logical Processes into the network.
• avnmp/java/start/Amain.java
Called from Flood.java. This starts an individual Logical Process on a single node.

Main Packages

• avnmp/java/lp
AVNMP Logical Process Classes
• avnmp/java/dp
AVNMP Driving Process Classes, currently includes the AVNMP Driver and actual load generation.
• avnmp/java/gvt
Global Virtual Time calculation classes
• avnmp/java/pp
Physical Process Classes, e.g. classes specific to the load prediction example application.
• avnmp/java/log
Write log file in HTML format.
• avnmp/java/plot
Write plot information in GnuPlot style format.

SNMP Instrumentation

• avnmp/java/snmp and avnmp/java/snmp/agent
This handles the SNMP interface to AVNMP.

Sample Application

• avnmp/java/load
This is a sample application that simply generates traffic. Its packet transmission rate and uptime are available through the active management framework.

avnmp.java.lp.ConfigInterface Parameters

• pdir
This is the directory in which the plot files are stored.
• logdir
This is the directory in which the log files are stored.
• rmlog
This is the script to remove old log files.
• rmsnmp
This is the script to remove old snmp data files.
• rmplots
This is the script to remove old plot files.

Operational Configuration Parameters

• setGenRate() in AvnmpSmartDriver
The rate at which virtual messages are generated.
• setStepSize() in AvnmpSmartDriver
The sample interval of virtual message values.
• setStepSize() in Amain
The sample interval of virtual message values.
• setGVTUpdate() in Amain
The rate at which GVT is determined.
• VirtualMessageRatio in Driver
The ratio of virtual to real messages.
• portTable in PP
A port/node mapping so that the virtual message can determine what port to check.
• PayLoad route in PayLoad
The payload holds the routing for the packet. That is, the packet is essentially source routed in order to maintain easy control.



AVNMP Architecture

AVNMP Dependencies

Specific ties to the Magician environment are noted in green.
Specific ties to the AVNMP-Enhanced application are in red.
Interfaces to SNMP are in pink.

AVNMP Dependencies Table

Class	Description	Magician Interfaces	Application Interfaces	Management Interfaces
Amain	Starts up an individual LP on a node. The steps to incorporate this into an execution environment.	This is an active packet and thus is highly Magician dependent.
AvnmpSmartDriver	Starts up an individual Driving Process on a node.	This is an active packet and thus is highly Magician dependent.
Flood	Starts Amain on all Active Nodes.	Magician dependent.
InjectSnmp	Injects the SNMP protocol interface in order to hold the predicted values and to manage the AVNMP system.			Primarily handles management functionality of instrumenting all active applications on the node with SNMP.
Driver	Generates virtual messages.	Magician dependent calls are made to NetLoggerEventManager and SPThread.currentSPThread.sleep()
Gvt	Global Virtual Time implementation.
HtmlDebug	Write HTML log files.
AvnmpBW	Add itself to the receive queue with some measurement hooks that are Magician dependent.	This is an active packet and thus is currently highly Magician dependent. queueSize() xmitRate() recvRate() Seconds() GetNodeName() smallstate access to add itself to the receive queue
SnmpInterface	Holds all the Object IDs of which AVNMP needs to be aware.			This is a management function.
ConfigInterface	Holds configurable information for the system.
AvnmpDebug	Set debug level.
AvnmpDriverRb		Accesses smallstate to notify DP of rollback.
AvnmpLP	The Logical Process			Many calls to the management interface.
AvnmpPacket	The virtual message (streptichron) - AvnmpPacket.compPred() checks the predicted accuracy by calling PayLoad.streptiChron().			Calls the management interface to accuracy of prediction with actual application. avnmp.java.lp.SnmpInterface holds the object id information for AVNMP and the application.
AvnmpQueue	General queue base class
AvnmpRecQueue	This is the logical process receive queue.		This is where AvnmpPacket.compPred() is called which ties to the application.	Calls the application via the management framework interface.
AvnmpSndQueue	Saves sent messages
AvnmpStat	(utility) Implements variable statistics.
AvnmpState	Logical Process state
AvnmpStateQueue	Logical Process State Queue			Includes updateSnmpObjects(). This is where the prediction is stored in the MIB.
AvnmpTime	Base class for time management.
PredMeasure	(utility) This is a utility to check the prediction accuracy weighted by time.
PredVector	(utility) Vector of PredMeasure objects.			Contains SnmpAgentContext.updateSubAgent().
GnuPlot	Write data to be plotted into GnuPlot files.
PP	This is the model of the process to be AVNMP-Enhanced.
PayLoad	No ties to Magician other than Node names for the route.		Highly application dependent. Contains source route for load prediction application.
splitElement, splitTable	Implements probabilistic routing.		Used in PayLoad to include probabilities of splits and joins in a route. Implements load application.
LoadGen	(Sample Application) Generates packets.	This is a Magician active packet.	This is the application.
LoadPacket	(Sample Application) Packets generated by LoadGen.	This is a Magician active packet.	This is the application.	Load and Uptime are available via the management interface.

The complete AVNMP documentation is found in the AVNMP API .